# Raspberry Pi Zero 2 W (aarch64) "Psion sidecar": an RS232 companion for a
# Psion 5MX. Two roles, split into submodules: ./serial-ppp.nix (PPP over the
# serial line, NAT out to wifi, telnet login) and ./email-proxy.nix (cleartext
# POP3/SMTP front end for the Psion's mail client). The raspberry-pi-3
# nixos-hardware profile (the Zero 2 W is the same BCM2837 SoC as the Pi 3) and
# key-only sshd (../../modules/ssh.nix) are layered on in the flake host table.
# Install notes: see ../../docs/hosts/pizero2w.md.
{ lib, ... }:
{
  imports = [
    ./hardware-configuration.nix
    ./serial-ppp.nix
    ./email-proxy.nix
  ];

  # Match the flake's nixosConfigurations attribute name so `nh os switch`
  # (which selects by the local hostname) resolves without an explicit -H flag.
  networking.hostName = "lyrathorpe-zero2w";

  # Headless server: modules/sway.nix is not imported and
  # features.swayDesktop.enable defaults to false, so this host keeps plain
  # TTY/SSH login.

  # Claude Code is a Node application. It runs on aarch64, but not usefully in
  # 512 MB of RAM, and its closure is unwelcome on an SD card.
  features.claudeCode.enable = false;

  # 512 MB total and no swap partition -- SD cards wear out under swap writes.
  # Compressed RAM swap instead; zstd is the best ratio-per-cycle the SoC can
  # sustain.
  zramSwap = {
    enable = true;
    algorithm = "zstd";
  };

  # The NixOS manual and man page index cost build time and a chunk of the card
  # for a box that is administered over SSH from elsewhere.
  documentation.nixos.enable = false;

  # Own the firmware partition declaratively: every switch rewrites config.txt,
  # the vendor device trees and the overlays below. Without this the card keeps
  # whatever config.txt the flashed image wrote and the UART overlays never
  # load. uboot.enable keeps the GPU firmware chainloading U-Boot -> extlinux,
  # which is how the NixOS aarch64 SD image boots; leaving it off would rewrite
  # config.txt without a `kernel=` line and the board would stop booting.
  hardware.raspberry-pi.firmware = {
    enable = true;
    uboot.enable = true;
  };

  hardware.raspberry-pi.configtxt = {
    settings.all = {
      # Headless: hand the VideoCore the minimum and leave the rest to Linux.
      # start_x/camera_auto_detect otherwise reserve VRAM for a camera stack
      # this board does not have.
      gpu_mem = 16;
      start_x = 0;
      camera_auto_detect = false;
      # Left on, the firmware auto-loads the KMS display overlay, which wants
      # more VRAM than this board can spare for a monitor it will never have.
      display_auto_detect = false;
    };

    # Replaces the profile's default (vc4-kms-v3d), which is display hardware
    # this host never uses.
    deviceTreeOverlays.all = [
      # Move the PL011 UART off Bluetooth and onto GPIO 14/15, so /dev/ttyAMA0
      # is the RS232 header. The mini UART (ttyS0) derives its baud rate from
      # the core clock and drifts at 115200.
      { disable-bt = { }; }
      # RTS/CTS on GPIO 16/17: the Psion's modem profile uses hardware flow
      # control, and so does pppd in ./serial-ppp.nix.
      { uart0.ctsrts = true; }
    ];
  };

  # Wifi is the Pi's uplink and the route the Psion reaches the internet over
  # (./serial-ppp.nix masquerades onto it).
  networking.interfaces.wlan0.useDHCP = true;
  networking.wireless = {
    enable = true;
    interfaces = [ "wlan0" ];
    # PSKs stay out of the Nix store: wpa_supplicant reads them at runtime from
    # this file, which is created on the device (root-owned, 0600) and contains
    #   psk_home=<the pre-shared key>
    # See ../../docs/hosts/pizero2w.md.
    secretsFile = "/var/lib/wpa_supplicant/secrets.conf";
    networks."CHANGE-ME-SSID".pskRaw = "ext:psk_home";
  };

  # The board takes a DHCP lease over wifi, so its address moves. mDNS makes it
  # findable as lyrathorpe-zero2w.local instead of hunting through the router's
  # lease table -- which matters most on first boot, when it is the only way in.
  services.avahi = {
    enable = true;
    openFirewall = true;
    publish = {
      enable = true;
      addresses = true;
      workstation = true;
    };
  };

  # Default-deny inbound. sshd opens 22 (../../modules/ssh.nix); everything the
  # Psion talks to is reached over the PPP link, which ./serial-ppp.nix marks
  # trusted.
  networking.firewall.enable = true;

  # See `man configuration.nix` / the stateVersion docs before changing.
  system.stateVersion = "26.05";
}